• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

Reasons Your fiat abarth key bravo key - Article - 500 Key Fob Won't Work

A key fob with the fiat 500 key fob reset 500 number is a handy way to unlock the doors and start the car. However, there are numerous reasons the fob could stop functioning. This could be due to a dead battery and water damage, as well as problems with the receiver modules, and interference.

This listing is for an NEW replacement Fiat Flip Key Remote that looks like the Ilco brand. It has to be professionally programmed (click here to search for local locksmiths for automotive locksmiths). Includes lock, unlock, and trunk buttons.

Dead Coin Battery

The most common reason your 500 key fob doesn't function is due to an inactive battery. Modern key fobs come with a limited operating range, and must be within only a few feet from the vehicle to operate. If you are not within your vehicle and you hit the keyfob, it will not respond and display the message "Key Fob Not Detected".

If this happens, simply replace the battery in the coin cell (Part number CR2032) by a new one from a reputable brand like Panasonic, Duracell, or Energizer. They are available at the local hardware store or online.

After you've replaced the coin cell battery It is possible to test it by standing next to your fiat doblo key replacement 500 and pressing the buttons. The parking lights will flash and the key fob should operate the lock and unlock switch.

If the fob's remote doesn't function after replacing the battery, it could have water damage that stops it from communicating with the receiver module inside your vehicle. Water damage can happen in a variety of ways, ranging from the slightest splash to submerging the fob into salt water at the beach. If you suspect your fob was exposed to water, try placing it in a dry rice bag to draw the moisture back out. If this does not work, you'll have to get your fob changed by an auto locksmith or dealer.

Water Damage

Water damage can happen if you immerse the fob into the ocean, or wash it in a washer. Saltwater poses a particular risk to the circuit board of the fob which causes it to short out and eventually end up dying. In the event that you let your fob get wet, it's not an ideal choice, but if you drop it in an empty cup of water, or do not remember to take it out of your pocket before you run the washing machine, don't give up hope.

First take the battery off the fob. Clean the electronic chip with isopropyl alcohol or another similar product and dry it thoroughly before replacing the battery. Check the fob again to see if it is working. If the key isn't working, it may need to be reprogrammed. This is typically done by a dealer or professional auto locksmith.

If the key is newer and has not been programmed to your car, it will likely need to be replaced completely. This is a simple procedure which can be accomplished by a professional locksmith for automotive use. The locksmith will need to cut the key to match the ignition on your vehicle. The locksmith will also have to program your fob into the vehicle's system. This is a quick and inexpensive process that can usually be completed within the next day.

Receiver Module Issues

One of the simplest reasons your 500 key fob might stop working is that it's simply out of range. The remote has a range of 30 feet. Therefore, in the event that you are far away from your vehicle it won't respond to your commands. This can easily be resolved by moving it closer to your vehicle until it starts responding.

If your fob doesn't work after replacing the battery inside the coin, which is also known as a "button", "watch" or "button" it could be due to a problem with the internal circuit board. Reprogramming your fob can resolve this problem. You can find instructions on how to do this for all automobiles by searching YouTube or reading the owner's manual.

It could be necessary to replace the metal clips that hold the coin batteries in place. If they loose tension, they could stop the battery from being properly seated and can cause your remote to malfunction.

In rare cases the fob could be desync'd with your vehicle due to software or hardware issues. This can be a major issue, but you are able to often fix this by visiting an auto locksmith to reprogram your fob. In certain instances the software may require reinstallation to your body control modules.

Interference

In addition to a dead coin battery The key fob may not be able to receive or transmit a signal due to interference. This can occur when the keyfob is located in close proximity to a radio transmitter such as a cell phone or radar detector. The key fob may not function because of a weak connection to the buttons, water damage or damage to the internal chips.

If the key fob been unable to function for a while without notice, or after trying every option at home to solve it e.g. replacing the battery, reprogramming, and using the spare key fob, you might have a malfunctioning receiver module on your 500. The receiver module, which is located beneath the dashboard, picks up radio frequency signals from your key fob. It converts them into electronic commands that the vehicle interprets.

Luckily, there is an easy way to reset all of the on-board systems in your 500 device, including the key fob. Disconnect the battery of 12 volts for approximately 15 minutes by disconnecting the negative cable first then the positive cable. Reconnect the battery. This will clear out any remaining electricity and restart the car's computer system, which can help get your key fob working again. If the problem persists you should seek the advice of an expert technician. They will be able to determine the exact cause of any problems.