• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

Why is My Car Ignition Locked?

There are a variety of reasons your ignition in your car may be locked. The key might be dirty or have a broken wafer in it. You can fix it by sliding the key into and out of the cylinder several times.

Another possibility is that the pins in the lock cylinder have become stuck. You can tap the cylinder gently using a small tack-hammer.

Check the Battery

If the car is in Park or neutral, but won't turn on when you insert the key into the ignition, there could be a problem with the shifter switch on the transmission. You can fix it by shifting the gear shifter upwards or downward to get the car into the correct gear.

If the car is still unable to turn, the problem could be related to the neutral safety cable or shifter in the transmission. A mechanic or a local auto ignition key replacement locksmith can fix these issues.

The ignition cylinder could also wear out. Over time, both the ignition and key may wear out, making them difficult to insert or remove. A lubricant such as silicon lock lubricant can solve this issue by allowing the silicon wafers to slide into place.

Lint from your pocket and adhesive from tape that holds packages together can also build up on the key, which prevents it from being able to slide into the ignition. You can clean the key with a cloth, or a cleaner such as Triflow to fix car ignition this issue. You could also try a spare key in order to determine if the issue is with the ignition or the key.

You could also tap the key using a small hammer when it's in the ignition. This can cause a slight vibration, which could be enough to loosen up the wafers in the ignition and allow them to slide into place. However, you must be careful not to scratch the ignition key or cylinder.

If all of the above solutions are unsuccessful, it's time to call a locksmith or automotive mechanic to have it looked at. It could be that the key is broken inside the ignition or it could be time to replace the whole thing. If the issue is with the key the locksmith will be able to make a new one for you. If the issue is related to the ignition cylinder, your car must be taken into a repair shop to have it replaced. Fortunately, these issues are typically very simple to fix.

Examine the Steering Wheel

A simple problem that can stop the ignition from turning is the steering wheel being locked. It can happen when a driver accidentally engages the steering wheel while they exit or enter the vehicle. This is usually caused by yanking the wheel while holding it against their body. It can also happen if a passenger in the rear seat accidentally engages the brakes as they get out of the vehicle.

Fortunately it's an easy fix that doesn't require a trip locksmiths or mechanics. First, check that the gear shift is in neutral or Park. If it's not you can gently pull or push the gear shifter until it moves to one of these positions. You should also activate the handbrake or press the brake prior to turning the key.

If the wheel isn't locked, a quick examination of the steering column should confirm that the key is in contact with the lock cylinder. This is typically identified by a small "Lock" label in the lower portion of the ignition circle. It is possible to disengage this by gently jiggling or pulling the keys with moderate force. It is important to not use too much pressure as this could cause damage to the key or break a wafer within the lock cylinder.

A spare key may also be used to disengage the lock. This could mean that the key is worn out and no longer able engage the wafers in the lock cylinder. If this is the case, a professional at Karl Chevrolet Webster City will be able to create a replacement key.

If the new key still does not engage, a short spray of oil that penetrates can help. Apply a small amount penetrating oil to the keyhole and ignition. Then, jiggle the key or tap it lightly to get it working. If this does not work, you may need to consult a specialist in your local dealership for cars. They can provide you with a new key and also replace the ignition cylinder, if required.

Check the Key

If you're unable to get your key to turn in the ignition, it is possible that there is a problem with your key. You can get rid of any foreign material (lint from packing tape or adhesive) from the key. It is also possible to rub alcohol or Goo Gone on the key to see if it helps.

If the pins in the lock do not move properly when you insert your key, it's possible that they are stuck. If you have a spare key to test, try putting it in the ignition and gently sliding it back out. You should be in a position to feel and hear the pins moving inside. If not, grease the pins using powdered graphite. You can buy graphite in small tubes that can be put directly into the keyhole. This should allow the pins to slide into position when you insert the key, and also prevent them from getting stuck.

A more serious issue is that it is worn or damaged, making it unable to engage the internal pins inside the ignition cylinder. This may cause the cylinder in the ignition to not turn and prevent you from starting your vehicle. If this is the case you'll need bring your car to a locksmith or repair shop for service.

If you can turn your car with a spare key and you have ruled out any problems with the battery or steering wheel it could be that the ignition cylinder has been worn out. You can try to loosen the lock with an abrasive screwdriver or handle of the hammer. Do not use the head. Tapping the cylinder gently can often release it and allow you to turn your key and start your car. If this doesn't work it is necessary to have the lock cylinder replaced by an expert mechanic.

Check the Ignition Socket

The ignition socket is where your key slides in and out of position when it is inserted. It is often gunked up with debris or as due to wear and wear and tear. Try putting some silicon lock lubricant (like WD-40) into the ignition to help things move along.

You can also make use of a small hammer to gently tap the interior of the ignition cylinder, to try to loosen or reset the pins that may be out of alignment. Again, be very careful not to overdo this, or you could cause significant damage to the van ignition repair switch.

Before you try this, make sure that the car's gearbox is either in park or neutral. Many newer cars have an option to lock the steering wheel when it is not in park or neutral and prevent the key from being turned in the ignition lock repair services.

If you've tried these steps but your key is still unable to turn, it could be that the ignition housing has to be replaced. Different vehicles have different methods for replacing the ignition cylinder, therefore it is important to follow the correct procedure.

This typically involves removing the plastic cover that covers the steering column and the ignition assembly. To remove this cover, you'll have to first adjust the tilt-wheel to the lowest setting and then loosen any fasteners that hold it in place.

After removing the cover you'll need to take off the old ignition cylinder from the steering column. Then, you'll have to compare the new auto ignition key replacement cylinder you purchased with the one you removed to make sure that they're identical. Once this is done the new ignition cylinder is able to be installed in the same way that the previous one was removed.

Sometimes, despite all of our efforts, the ignition will become damaged and need to be replaced. If this happens, it's recommended that you contact a Tempe Locksmith for assistance. A locksmith can assist you in selecting the right replacement and install it properly to ensure that your car will be able to start up again.