• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

Billiards uses only three balls - one red and two white (or one red, one white, and one yellow). Although billiard balls’ material originally was ivory, three creative pool ball materials exist nowadays. This material has many applications for flooring and countertop refinishing. ‘Billiards’ and ‘pool’ are two words that are often interchanged because they refer to games played on similar-looking tables with a cue and balls. Apply some torque to the plug and feel the two pin stacks with your pick. Reset the lock by returning the plug to the vertical locked position and try again but with torque applied in the other direction. If pushed up, it eventually sets and the plug turns slightly (and the pin stack's state changes to set/not-binding). Set/not-binding. The pin stack was already picked. Once you do this, one of the pins will be in the unset/binding state while the other (the one you set) will be in the set/not-binding state . If you release pressure with your pick while still applying torque, the bottom pin will drop freely, and will not have any spring pressure if you try to push it back up.

In particular, you should feel when you set a pin as much in the torque tool as you do in the pick. Now apply torque in the other direction. Now the plug is being prevented from moving by the next most misaligned pin (which, in this case, is the other pin, since there are only two). Now release torque and try again, but this time lift the pins as little as you can when you test them, while still distinguishing between the two states. Now the top pin is above the shear line and the bottom pin is below it. When the plug turned slightly, it trapped the top pin above the shear line, preventing it from re-entering the plug. Learn to apply the minimum amount of torque needed to turn the plug. One of them should feel springy, just as it did with no torque applied. First, apply light torque (as you practiced in the previous exercises) to the two pin cylinder and gently feel each pin. Keep practicing with the two pin lock, trying to lighten your touch as you do, and making sure you consistently can pick the pins one at a time. For this exercise, you'll use your torque tool and pick on the two pin lock to put the pins in each of these states to learn what they feel like with your pick.

Practice picking the two pin lock until you can do it easily and naturally. A pin stack in a lock being picked might be in any of four states: Unset/not-binding. It's binding because it's the one most out of alignment in the direction you're turning, and so its top pin is being pinched (gently) between the plug and the shell. So we don’t realize that we’re living out of now and throwing the past behind us. Apply very light torque while energetically moving the sawtooth rake in and out of the keyway. If both feel springy, you're not applying enough torque (which is unlikely). Your goal is to learn to do this with the absolute minimum amount of torque needed to bind the most misaligned pin enough to distinguish it from the other one. Insert the tip of the tool in the keyway, allowing enough room for your pick to enter and manipulate the pins. Much of lock picking skill depends on testing pins stacks for the purpose of finding which to push up next and assuring that no pins are overset. One of the pins should be unset/binding ("squishy") while the other should be unset/not-binding ("springy").

Continue with the one pin lock, trying to apply less and less torque each time. Several positions are possible; here a vertically-oriented torque tool is used at the top of the keyway. These skills become very important when picking better quality locks, so take your time here. Spend more time on this exercise than you think you need to; most people never learn to properly apply the light touch needed to pick better quality locks. Develop a light touch. I usually find that the very top of the plug, directly in front of the pins, to be a good place to apply torque, but you have to be careful that the tool doesn't touch the front-most pin. Vary the amount of lifting between strokes but do not force the pins, lest you overset them. Is they find their aiming line, set up correctly, and then they decide to move and change their aim while they’re taking their practice strokes. Again, repeat the exercise with the aim of learning to distinguish between these states with as little lifting as possible. Repeat this exercise until you can reliably distinguish between a binding and a non-binding pin with very little lifting. In lock picking terminology, we say that the pin statck is binding.

If you have any kind of questions concerning where and how you can utilize what is billiards, you could contact us at our own site.